avrdude: Can't find programmer id "-q"

You are viewing a static version of the site. Enable JavaScript to benefit from the full functionality of this site and enable such things as forum posting.avrdude: Can't find programmer id "-q"pappastech:

After an upgrade to UECIDE (and no changes to a code base that's worked for years) I'm not getting the following error message when trying to program a Nano. I've looked around for a solution to no avail. It seems obvious that the wrong programmer is somehow selected, but I've tried removing and re-installing it with no success. Any thoughts?

Respectfully, Tom

<pre><code> Uploading firmware... • Resetting board... • Uploading sketch...

Valid programmers are: 2232HIO = FT2232H based generic programmer 4232h = FT4232H based generic programmer 89isp = Atmel at89isp cable abcmini = ABCmini Board, aka Dick Smith HOTCHIP alf = Nightshade ALF-PgmAVR, http://nightshade.homeip.net/ arduino = Arduino arduino-ft232r = Arduino: FT232R connected to ISP arduinoisp = Arduino ISP Programmer arduinoisporg = Arduino ISP Programmer atisp = AT-ISP V1.1 programming cable for AVR-SDK1 from <http://micro-research.co.th/> atmelice = Atmel-ICE (ARM/AVR) in JTAG mode atmelice_dw = Atmel-ICE (ARM/AVR) in debugWIRE mode atmelice_isp = Atmel-ICE (ARM/AVR) in ISP mode atmelice_pdi = Atmel-ICE (ARM/AVR) in PDI mode atmelice_updi = Atmel-ICE (ARM/AVR) in UPDI mode avr109 = Atmel AppNote AVR109 Boot Loader avr910 = Atmel Low Cost Serial Programmer avr911 = Atmel AppNote AVR911 AVROSP avrftdi = FT2232D based generic programmer avrisp = Atmel AVR ISP avrisp2 = Atmel AVR ISP mkII avrispmkII = Atmel AVR ISP mkII avrispv2 = Atmel AVR ISP V2 bascom = Bascom SAMPLE programming cable blaster = Altera ByteBlaster bsd = Brian Dean's Programmer, http://www.bsdhome.com/avrdude/ buspirate = The Bus Pirate buspirate_bb = The Bus Pirate (bitbang interface, supports TPI) butterfly = Atmel Butterfly Development Board butterfly_mk = Mikrokopter.de Butterfly bwmega = BitWizard ftdi_atmega builtin programmer C232HM = FT232H based module from FTDI and Glyn.com.au c2n232i = serial port banging, reset=dtr sck=!rts mosi=!txd miso=!cts dapa = Direct AVR Parallel Access cable dasa = serial port banging, reset=rts sck=dtr mosi=txd miso=cts dasa3 = serial port banging, reset=!dtr sck=rts mosi=txd miso=cts diecimila = alias for arduino-ft232r dragon_dw = Atmel AVR Dragon in debugWire mode dragon_hvsp = Atmel AVR Dragon in HVSP mode dragon_isp = Atmel AVR Dragon in ISP mode dragon_jtag = Atmel AVR Dragon in JTAG mode dragon_pdi = Atmel AVR Dragon in PDI mode dragon_pp = Atmel AVR Dragon in PP mode dt006 = Dontronics DT006 ehajo-isp = avr-isp-programmer from eHaJo, http://www.eHaJo.de ere-isp-avr = ERE ISP-AVR <http://www.ere.co.th/download/sch050713.pdf> flip1 = FLIP USB DFU protocol version 1 (doc7618) flip2 = FLIP USB DFU protocol version 2 (AVR4023) frank-stk200 = Frank STK200 ft232r = FT232R Synchronous BitBang ft245r = FT245R Synchronous BitBang futurlec = Futurlec.com programming cable. jtag1 = Atmel JTAG ICE (mkI) jtag1slow = Atmel JTAG ICE (mkI) jtag2 = Atmel JTAG ICE mkII jtag2avr32 = Atmel JTAG ICE mkII im AVR32 mode jtag2dw = Atmel JTAG ICE mkII in debugWire mode jtag2fast = Atmel JTAG ICE mkII jtag2isp = Atmel JTAG ICE mkII in ISP mode jtag2pdi = Atmel JTAG ICE mkII PDI mode jtag2slow = Atmel JTAG ICE mkII jtag2updi = JTAGv2 to UPDI bridge jtag3 = Atmel AVR JTAGICE3 in JTAG mode jtag3dw = Atmel AVR JTAGICE3 in debugWIRE mode jtag3isp = Atmel AVR JTAGICE3 in ISP mode jtag3pdi = Atmel AVR JTAGICE3 in PDI mode jtagkey = Amontec JTAGKey, JTAGKey-Tiny and JTAGKey2 jtagmkI = Atmel JTAG ICE (mkI) jtagmkII = Atmel JTAG ICE mkII jtagmkII_avr32 = Atmel JTAG ICE mkII im AVR32 mode linuxspi = Use Linux SPI device in /dev/spidev* lm3s811 = Luminary Micro LM3S811 Eval Board (Rev. A) mib510 = Crossbow MIB510 programming board mkbutterfly = Mikrokopter.de Butterfly nibobee = NIBObee o-link = O-Link, OpenJTAG from www.100ask.net openmoko = Openmoko debug board (v3) pavr = Jason Kyle's pAVR Serial Programmer pickit2 = MicroChip's PICkit2 Programmer picoweb = Picoweb Programming Cable, http://www.picoweb.net/ pony-stk200 = Pony Prog STK200 ponyser = design ponyprog serial, reset=!txd sck=rts mosi=dtr miso=cts powerdebugger = Atmel PowerDebugger (ARM/AVR) in JTAG mode powerdebugger_dw = Atmel PowerDebugger (ARM/AVR) in debugWire mode powerdebugger_isp = Atmel PowerDebugger (ARM/AVR) in ISP mode powerdebugger_pdi = Atmel PowerDebugger (ARM/AVR) in PDI mode powerdebugger_updi = Atmel PowerDebugger (ARM/AVR) in UPDI mode siprog = Lancos SI-Prog <http://www.lancos.com/siprogsch.html> sp12 = Steve Bolt's Programmer stk200 = STK200 stk500 = Atmel STK500 stk500hvsp = Atmel STK500 V2 in high-voltage serial programming mode stk500pp = Atmel STK500 V2 in parallel programming mode stk500v1 = Atmel STK500 Version 1.x firmware stk500v2 = Atmel STK500 Version 2.x firmware stk600 = Atmel STK600 stk600hvsp = Atmel STK600 in high-voltage serial programming mode stk600pp = Atmel STK600 in parallel programming mode ttl232r = FTDI TTL232R-5V with ICSP adapter tumpa = TIAO USB Multi-Protocol Adapter UM232H = FT232H based module from FTDI and Glyn.com.au uncompatino = uncompatino with all pairs of pins shorted usbasp = USBasp, http://www.fischl.de/usbasp/ usbasp-clone = Any usbasp clone with correct VID/PID usbtiny = USBtiny simple USB programmer, https://learn.adafruit.com/usbtinyisp wiring = Wiring xil = Xilinx JTAG cable xplainedmini = Atmel AVR XplainedMini in ISP mode xplainedmini_dw = Atmel AVR XplainedMini in debugWIRE mode xplainedmini_updi = Atmel AVR XplainedMini in UPDI mode xplainedpro = Atmel AVR XplainedPro in JTAG mode xplainedpro_updi = Atmel AVR XplainedPro in UPDI mode </code></pre>

matt:

This is actually a failing of my boards conversion script. It thinks there should be am upload protocol option for that board in the boards.txt file, but there isn't. I'll need to fudge my script around it. One mo...

matt:

Ok. I have rewritten the menu conversion system in my convert script to be far more generic - using a reactive instead of predictive model. It should catch everything correctly now. If you update the board in the plugin manager to version 1.2.0 it should work perfectly now (fingers crossed).

pappastech:

Awesome! That fixed it.

Thank you!

Support Us

Running this server costs money. This server not only hosts this website, but is also the main build platform for creating the download files for UECIDE. Just a couple of pounds (or Dollars, Yen, Mongolian tögrög... we're not fussy) can help to offset the costs.

Alternatively, if you want to be more personal, you could buy me something on Amazon. I have a small wish-list of low-cost items that I'd quite like to receive. Make it a surprise.

UECIDE

|juˈekaɪdiːˈiː| :: Wake Up Your Arduino

Support Us